Work on the tiny house has been pretty slow as we’re finishing up the interior. Since I last posted we’ve finished up the kitchen counters and started installing the sink and 2 burner gas stove. We built a ladder to access the larger of the two lofts (the smaller one will have a collapsible ladder, as it’ll get used less). The ladder we built attaches to the loft around a metal rod, allowing it to slide to the middle of the floor for use, and back to the side to stay out of the way. We’re in the process of building a couch that folds out to sleep another 2 people. The arms on the side and railing at the back fold down to support the top when it converts to a bed. There will be 2 doors underneath with storage under the couch. We built a small table that attaches to the wall with piano hinges and is held up by a triangular support that is hinged to the wall. Once all the furniture is finished the house should be able to sleep 4 people with features that fold up to make it roomier if just 1 or 2 are staying.
We still need to build a box to go around the hot water heater, run gas to the stove and figure out a solution for electricity. We’re aiming to move it in March and are finishing up what we can before we go. My parents have had land cleared out where they are going to park it once its moved. The land was leveled and gravel laid down. The land is supposed to be getting city water run to it, but we’ll need to find out own solution for waste water disposal. We’d like to install solar, but haven’t started working on it yet. We’ll also be buying a small generator as a back up for the solar, or to tide us over until we can get the solar installed.
Couch folded out to seat two
Ladder with routed hand holes
I promised my mom I would make the cabinets and counters for the house, but then I got distracted. Before I even got started planning my dad started building. I’m glad he did because I’m sure the cabinets will turn out much nicer now. We were originally going for stark simplicity, but my dad loves a challenge and has been designing and fitting drawers, shelves and doors. Today we got 3 drawers put in. It was pretty challenging and took most of the day’s work. In the end they fit well and move smoothly. They look rough now because they’re just set in the shell of the counter, but soon we’ll finish the rest of the cabinetry and put faces and pulls on the drawers. We were also able to cut all of the pieces for the other set of counters, on the opposite wall.
The work is going a lot slower now as the days get shorter, but every week it looks a little less like a box full of lumber and supplies and a little more like an actual house.
Jason an my dad discussing drawer measurements
Every week it looks less like a box full of lumber and tools and more like a (tiny) house
Today we got started working on what will be the tiny kitchen. With the floors, interior paneling and window trim installed it was time to start planning the cabinets. Our plan calls for a kitchen that’s situated right under the larger of the two lofts. It will have cabinets on both walls with a sink on one side with a two burner propane stove and mini refrigerator on the other. For the cabinets we decided to build a simple frame that we would fit the appliances and drawers, shelves and cabinets into. The outside will be finished with a 1/4 inch cedar and the top is a slab of spruce stained a dark color to match the flooring.
We started building the frame today, which gave my dad an excuse to buy a new tool (always fun). After starting the cabinet frame we had just enough time to cut the counter top and mount it before positioning the sink. We plan on connecting the plumbing (PEX tubing) later. The sink we bought was a small stainless steel bar sink that was just the right size for the narrow counters.
Working in the fall has been a nice relief from the heat of the summer. During the early months we started early when we were heaving plywood up to the roof and installing paneling on a scaffold. We’d work until it was too dark to work anymore. Now that its cooler and the projects needed to finish the build are getting less taxing, we’ve been starting earlier and quitting sooner. With lights inside and a fan/space heater as required the work is less draining and more fun than the initial steps. Since we’ve delayed the launch date until spring there’s also less pressure to finish it soon. We’re finding that like any project, it’s going to take about twice as long as initial guesses.
Joining the frame boards
Joined frame boards
One day’s cabinet progress